.: XT660.com - The #1 XT660 Resource :.
Page 4 of 10 « First 2 3 4 5 6 Last »
Show 40 post(s) from this thread on one page

.: XT660.com - The #1 XT660 Resource :. ( https://www.xt660.com/index.php)
-   XT660Z Mods ( https://www.xt660.com/forumdisplay.php?f=165)
-   -   Cheap footpegs from eBay ( https://www.xt660.com/showthread.php?t=13425)

Gas_Up_Lets_Go 20-04-10 18:19
Quote:
Originally Posted by stuxtttr (Post 126538)
I may even go with port and starboard:Gangsta2_9BI664:
Red & Green - Cool!

deiaccord 01-05-10 15:48
1 Attachment(s)
Got mine today from the uk listing, delivered in a week ast a cost of �12 http://cgi.ebay.co.uk/ws/eBayISAPI.d...ht_4239wt_1167

The Pegs are nearly twice as wide as the stock pegs and stick out slightly further as the peg grips start a big further out than stock (see attached pic)

Fitting is pretty straightforward even for a mechanicaly inept person such as myself:
Straighten and then remove retaining pin holding the bolt.
Remove the bolt, then pull off the peg/spring.

Put the spring in the new peg.
Refit the large bolt to hold in the new peg and the spring (this is the hard bit trying to keep them aligned to make it easy)
Refit the retaining clip.
For tools all I used was a pair of long nose pliers.

I've not had a chance to ride with them on properly yet but they do seem to very much improve comfort and stability on the pegs.

Quality seems reasonable, probably nothing more than cast iron/steel and a bit heavier than stock but a bargin overall for the price.

zOU 01-05-10 18:10
Quote:
Originally Posted by deiaccord (Post 127669)
I've not had a chance to ride with them on properly yet but they do seem to very much improve comfort and stability on the pegs.
I posted comparative pictures on the previous page too ;)

THey're really good and offer improved control and comfort :)

weeksy 01-05-10 18:23
Anyone know yet if they fit the XTX ?

Will have a set if they do. I recall loving my KTM 950SMR pegs and these look very very much the same.

iShoe 13-05-10 17:11
Anyone know yet if they fit the XTX ?

Wayne 13-05-10 22:50
Foot Pegs
 
I agree that the OEM pegs on the Tenere leave a lot to be desired, and after having my foot slip off during a maneuver in heavy traffic in the rain (and almost loosing control - an "underpants moment") I started to look for a bolt on alternative. I came upon Pivot Pegz http://www.pivotpegz.net/. At 150 euro a pair they are nowhere near the price of the bargain mentioned below, but they are TUV approved and Excellent quality. The first ride was a little weird at first, but after a few rides in slippery and tight conditions the difference is amazing. Vibration is about the same as the OEM pegs but the difference in feel and control is impressive. If you can just ignore the price ........ and don't tell the wife. :)

Niek 08-06-10 14:25
Quote:
Originally Posted by weeksy (Post 127681)
Anyone know yet if they fit the XTX ?

Will have a set if they do. I recall loving my KTM 950SMR pegs and these look very very much the same.
I would not be surprised if the KTM pegs also fit. Will have a look in my garage.

Thanx for the tip anyway, bought them also and they are perfect value for money.

Lairyboy 08-06-10 15:25
Quote:
Originally Posted by Wayne (Post 128734)
I agree that the OEM pegs on the Tenere leave a lot to be desired, and after having my foot slip off during a maneuver in heavy traffic in the rain (and almost loosing control - an "underpants moment") I started to look for a bolt on alternative. I came upon Pivot Pegz http://www.pivotpegz.net/. At 150 euro a pair they are nowhere near the price of the bargain mentioned below, but they are TUV approved and Excellent quality. The first ride was a little weird at first, but after a few rides in slippery and tight conditions the difference is amazing. Vibration is about the same as the OEM pegs but the difference in feel and control is impressive. If you can just ignore the price ........ and don't tell the wife. :)

Funny that, my missus thinks that everything I buy for my bike is no more than �20.......cheapest bike I've ever owned according to her.........wonder where she gets that idea from?:icon_rabbit:

mudmatt 13-06-10 18:48
Just ordered mine

Niek 14-06-10 16:06
Quote:
Originally Posted by Niek (Post 130539)
I would not be surprised if the KTM pegs also fit. Will have a look in my garage.
No they don't, KTM's mountings are wider


All times are GMT +1. The time now is 09:10.
Page 4 of 10 « First 2 3 4 5 6 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.