Hi kev,

What map do you suggest to run the bike in when its rebuild?
I saw that there were different 700 maps but i dont know which one to take.

Custom map by Marjani - XT660.com; created 5-9-09.
103mm Big Bore|Nicasil cylinder (PowerSeal)|JE piston|CR 11,3:1|ported head (OTR)|Tuned cam (OTR)|PCIII|BSM exhausts|+4mm� larger exhaust pipes (OTR)|DNA stage 1 & 2 Filters|AIS blocked|Rerouted engine breather hose
63,33HP/6500rpm - 75,68 Nm/5500rpm

2005 Yamaha XT660X European model 700CC conversion
Akrapovic exhaust no silencer
DNA Stage 3 air box Kit
AIS closed
In later models Map must be used with oxygen sensor eliminator
Maped by T2NE


XT700 big bore only XTX cam
Raptor 700 conversion 11:1 piston
Carbon Cans
DNA stage 1 & 2 filters
O2 Eliminator
Snorkel out
CO1 set to Zero
98 RON fuel
AIS blocked
53.29 HP @ 6100RPM
50.51 Ft-lbs torque @ 4800RPM
I still need to do more work on this map on the dyno so use it as a guide only.



XT700 big bore only XTX cam
Raptor 700 conversion 11:1 piston
Carbon Cans
DNA stage 1 & 2 filters
O2 Eliminator
Snorkel out
CO1 set to Zero
98 RON fuel
AIS blocked
53.29 HP @ 6100RPM
50.51 Ft-lbs torque @ 4800RPM
I still need to do more work on this map on the dyno so use it as a guide only.

Thanks!! :icon_joker:

With the engine work you have done I would be getting your own custom map built.

You can try the ones mentioned to see what the motor likes but a custom map will always produce the best results.

hmm thought i only needed to make a custom map after it ran in (500km), but thanks again! Haha

Some new pic's of the head and the akrapovic cans with new stickers.

http://i61.tinypic.com/dg2kc4.jpg

http://uploadenfoto.nl/pictures/cf26...2b8d34.jpg</a>
http://uploadenfoto.nl/pictures/49daf732a0f997b6773ad54739c7beda.jpg



Thom

Today i visited the powdercoater again :055:

http://i57.tinypic.com/2ce27mx.jpg
http://i62.tinypic.com/312vhfl.jpg
http://www.imagedump.nl/
http://www.imagedump.nl/

Hello,

I'm trying to make a replica of the DNA stage 3 airbox because original it's to expensive (�700).
Total expenses:
1x 2nd hand airbox �25
1x K&N Filter RC-9410 �48
3x 14mm filter �25
1x Silicone hose 51>76mm �13

Pic's so far.

http://i57.tinypic.com/2dsizxt.jpg

http://i61.tinypic.com/dnyniu.jpg

Greetings,
Thom

Looking very good, had a similar setup to my XT:
stock 100mm, 11:1 CP piston, OTR camshaft and flowed head.
Gave a nice gain and a much sportier feel (fast throttle response and more pull).

Veel succes en veilige km's!
Groeten uit Den Haag ;)

Haha bedankt! Hoe reed hij op de testbank? of is die nooit op de testbank geweest?

Little update on the airbox, fitted small filters.
http://i58.tinypic.com/2d9db12.jpg

http://i60.tinypic.com/2u7yjb7.jpg

Build in the main filter http://www.motor-forum.nl/global/smileys/smile.gif
Only the inlet pipe wasn't good so i used a plastic pipe.

http://i61.tinypic.com/2r70vtv.jpg

Only need to paint the pipe black (between filter and TB) and round everything up.

Looking good, any close up photo's of the main filter & intake?