![]() |
![]() |
![]() |
|
|
XT660Z T�n�r� Tech Section Tyres, Mods, Luggage & Long distance preparation |
![]() |
|
Thread Tools | Display Modes |
#
1
|
|||
|
|||
Pciii
So, I've been given a PCIII for nothing, only one problem....it's for a Honda VFR. What's the go with retro fitting them to other bikes, namely my Ten? Can the plugs just be rewired? Can the bike just be hard-wired?
Are the wiring of the PCIIIs just generic and only the plugs different between bikes? Shame to waste it...any ideas/suggestions. |
#
2
|
||||
|
||||
I would sell it on EBay & buy the correct one.
__________________
Click here to join the XT Supporter's scheme Mods that I have done to my XTX's My 04 XTX Stage 1 & 2 DNA filters / Kev fuel mod / snorkel mod / Drilled air box mod / Engine breather mod / Fork Spacer mod / 15w fork oil / [ My 07 XTX Raptor 700 cylinder 102mm / Modified Crank Case to take a 105mm Raptor Cylinder / 11:1 102mm JE Raptor piston / Stage 1 Raptor Hot Cam / Ported head / Colder Spark Plug / +2mm Throttle body / DNA stage 1 & 2 filters / Modified Air Box / Snorkel removed / Worry Brothers stage 2 filter cover / 6mm & 8mm Bolts Replaced with Titanium Bolts / Recovered seat in Black / O2 Eliminator / My 09 XTX 59HP at the rear wheel / Stage 2 Raptor Hot Cam / DNA stage 3 Air Box / Carbon Can Exhausts / Modified Exhaust Link Pipes / PCIII With Custom Fuel Map / Wideband Commander O2 Data logger / LCD100 Dyno Jet display & fuel adjuster / 2500 OHM HT lead instead of a 10K OHM XT lead / Extra Coolant Cooler / Protaper Fat Bars / Tail Tidy With LED Tail Light / OKE Protection Knobs / LED indicators / AIS blocked / Modified rear sprocket rubbers / Rear Foot Pegs removed / 09 ECU With 02 Sensor Changed To A 06 ECU / Complete wiring harnes Changed from 09 to 04 / Home made LED resistor flasher / Hole drilled in the fuel tank filler neck to allow quicker filling / Modified Bar End Weights / Progressive front fork springs, 15W fork oil, forks lowered 25mm, used XTR rear links lowering the rear 20mm, rear spring one click stiffer / Changed front & rear guards from blue to black / 47T rear sprocket / Speedo Healer V4.0 / Kev throttle cam mod / Throttle grip mod / The new 2010 O2 sensor mod is out, works a treat, The new 2012 O2 Controller is out, PM me for details Now ride a 2018 MT09SP ABS + TCS My KTM 990 SMR Mod book. http://www.ktmsmt.com/viewtopic.php?f=13&t=4946 ![]() |
#
3
|
|||
|
|||
Thanks Kev, I am contemplating that, just as it was given to me I'm hesitant selling as that's what they could have done but wanted to do me a favour. Was hoping someone had done similar and tracking down the ECM plugs and a wiring diagram wouldn't be too hard.
Mat. |
Sponsored Links |
#
4
|
||||
|
||||
No use looking for the plugs unless all the inputs & outputs are the same.
It's not as easy as just swapping the plugs, are both bikes TPS voltage ranges the same? are both bikes crankshaft impulse pickup voltages the same outputs? are the injector duty cycles simular? Is the Pulsed width modulated wave form the same on both bikes injectors?
__________________
Click here to join the XT Supporter's scheme Mods that I have done to my XTX's My 04 XTX Stage 1 & 2 DNA filters / Kev fuel mod / snorkel mod / Drilled air box mod / Engine breather mod / Fork Spacer mod / 15w fork oil / [ My 07 XTX Raptor 700 cylinder 102mm / Modified Crank Case to take a 105mm Raptor Cylinder / 11:1 102mm JE Raptor piston / Stage 1 Raptor Hot Cam / Ported head / Colder Spark Plug / +2mm Throttle body / DNA stage 1 & 2 filters / Modified Air Box / Snorkel removed / Worry Brothers stage 2 filter cover / 6mm & 8mm Bolts Replaced with Titanium Bolts / Recovered seat in Black / O2 Eliminator / My 09 XTX 59HP at the rear wheel / Stage 2 Raptor Hot Cam / DNA stage 3 Air Box / Carbon Can Exhausts / Modified Exhaust Link Pipes / PCIII With Custom Fuel Map / Wideband Commander O2 Data logger / LCD100 Dyno Jet display & fuel adjuster / 2500 OHM HT lead instead of a 10K OHM XT lead / Extra Coolant Cooler / Protaper Fat Bars / Tail Tidy With LED Tail Light / OKE Protection Knobs / LED indicators / AIS blocked / Modified rear sprocket rubbers / Rear Foot Pegs removed / 09 ECU With 02 Sensor Changed To A 06 ECU / Complete wiring harnes Changed from 09 to 04 / Home made LED resistor flasher / Hole drilled in the fuel tank filler neck to allow quicker filling / Modified Bar End Weights / Progressive front fork springs, 15W fork oil, forks lowered 25mm, used XTR rear links lowering the rear 20mm, rear spring one click stiffer / Changed front & rear guards from blue to black / 47T rear sprocket / Speedo Healer V4.0 / Kev throttle cam mod / Throttle grip mod / The new 2010 O2 sensor mod is out, works a treat, The new 2012 O2 Controller is out, PM me for details Now ride a 2018 MT09SP ABS + TCS My KTM 990 SMR Mod book. http://www.ktmsmt.com/viewtopic.php?f=13&t=4946 ![]() |
#
5
|
|||
|
|||
Grammys
Quote:
I.e most ecms I work with are programmed to accept TPS in either digital PWM or analog potentiometer. Never seen an injector that wasn't PWM and the DC depends on the crank speed, although the output voltage can vary especially with Piezo injectors upto 160v. I guess that also goes with crank position, modern common rail diesels being released still running inductive pickup position sensors while some are more expectedly running Hall effect. Again all are programable into the ECM depending on the chassis electrics the engine ecms are mated with and this isn't even going into the rest of the nodes on the network. |
![]() |
Thread Tools | |
Display Modes | |
|
|