.: XT660.com - The #1 XT660 Resource :.
Page 2 of 3 1 2 3
Show 40 post(s) from this thread on one page

.: XT660.com - The #1 XT660 Resource :. ( https://www.xt660.com/index.php)
-   XT660Z T�n�r� Tech Section ( https://www.xt660.com/forumdisplay.php?f=163)
-   -   Consumables / Spare Parts ( https://www.xt660.com/showthread.php?t=8747)

tripletom 14-01-09 23:07
Looks quite like the FZR600 3HE as well, I'd need to check, which means I'd need to find the box that has the FZR600 3HE parts in...I may be some time...

scottnet 27-02-09 12:09
Bearings
 
Genuine Yamaha bearings are a horrfic price. The advice I have had is that SKF are best quality. Here are the part no's you need.

Front & rear : 6203-2RS http://www.bearingboys.co.uk/6203-2R...Bearing-1889-p

Sprocket carrier 6304-2RS http://www.bearingboys.co.uk/6304-2R...Bearing-1930-p

JMo 28-02-09 00:41
Thanks scottnet - presumably the front and rear bearings are the same, and the same each side of the hub? do you know how many you need? (two each wheel presumably?)

xxx

russolivant 28-02-09 09:07
2 x 6203 for the front
2 x 6203 for the rear
1 x 6304 for the sprocket carrier

JMo 28-02-09 16:59
Excellent - thanks for confirming those Russ - I fear I'm going to be needing some of those when I get home!


xxx

JMo 02-03-09 02:14
Quote:
Originally Posted by scottnet (Post 84189)
Genuine Yamaha bearings are a horrfic price. The advice I have had is that SKF are best quality. Here are the part no's you need.

Front & rear : 6203-2RS http://www.bearingboys.co.uk/6203-2R...Bearing-1889-p

Sprocket carrier 6304-2RS http://www.bearingboys.co.uk/6304-2R...Bearing-1930-p
Forgive me questioning Scottnet, but are you sure about the part number for the sprocket carrier? I had a look at the link above and it says the internal diameter is 20mm - shouldn't it be 17mm the same as the axle bearings?

xxx

scottnet 03-03-09 18:30
It is 20mm ID, in the sprocket carrier there is spacer that reduces the ID to 17mm for the axle

It's always good to check

JMo 03-03-09 22:28
Quote:
Originally Posted by scottnet (Post 84614)
It is 20mm ID, in the sprocket carrier there is spacer that reduces the ID to 17mm for the axle

It's always good to check
Aha, thanks for confirming that Scott, I wondered if that was the case - like you say, best to make sure xx

scottnet 14-03-09 13:18
Levers
 
For levers see http://www.xt660.com/showthread.php?t=8908

JMo 19-03-09 01:25
Me again...

Does anyone know the part numbers for the steering/head bearings... not that I need them yet, just wanting to cross reference the numbers though...

Many thanks,

Jenny xx


All times are GMT +1. The time now is 01:21.
Page 2 of 3 1 2 3
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.