rpm increase
 

Hi can anyone tell me how to increase the rpm of my bike from 1080 to 1300rpm?Thanks

In the photos you will see a screw on the right of the photo, turn this screw clockwise & this will increase the idle speed. I would set your idle once the engine is warm to around the 1500rpm mark.:023:

thanks for the reply kev and another question how can i see the idle rpm in the screen panel?or i cannot?

Switch off Engine Run switch, switch OFF Key switch.

1/ Press both SELECT & RESET buttons and then switch ON Key switch, keep SELECT & RESET buttons pressed for at least 8 seconds. Display then changes to "DIAG". Release SELECT & RESET buttons.

2/ Press the SELECT button once until CO displays, press SELECT & RESET buttons again & hold, CO1 should display.

3/ Once selected CO1, switch on the kill switch & crank the motor. Once started the rev counter should be in the right side of the LCD screen.

:icon_thumright: thanks

'

Will the rev counter bee there "for ever" or just to the next time you turn the engine of and on?

If you want to see the rev counter you have to repeat these steps every time before you start the bike.

Thanks

Hi. I cannot see any photos, can you tell me where the idle adjustment screw is please ? Cheers - Steve

Idle screw.

Cheers :-)

I tried this but all i get displayed is the word co,I held down the select and preset buton then switched the ignition on untill the word diag comes on the screen,I then pressed select untill co appears then switch the cut off button to on and start the engin and all that is displayed is the word co.
Am i doing something wrong or is it different on the 07 model.
Thanks,Andy

It`s ok i have sussed how to do it now,My co1 reading is set to 14 and i am getting a little surging at low speed and the bike cuts out now and then,Would it be a good idea to increase this or should i leave alone.
Thanks,Andy

Is it possible to start the engine while in diag mode ?
I tried and didn't succeded.

Going off the top of my head at the moment but do as kev said....

Switch off Engine Run switch, switch OFF Key switch. Press both SELECT & RESET buttons and then switch ON Key switch. Keep SELECT & RESET buttons pressed for at least 8 seconds. Display then changes to "DIAG". Release SELECT & RESET buttons.
Select CO1 mode by pressing the SELECT button.

Then press both the select and reset buttons together until you hear a click.

Then you will see a "0" in the top right of your speedo.

Then start your bike and you can see your rpm.

Hope this is correct as my bike is somewhere else at the moment.

just tried it, works a treat, you guys ROCK

Cheers :headbang:

hey andy, mine was also at 14, i removed the snorkel and put it up to 17 and runs a lot smoother in lower revs now, i would recommend doing it, my bike feels a lot smoother, bring on the $$ for a stage 2 DNA filter i say!!!:deathmetal[1]:

BTW... :lostthread[1]:!!!!!!!!!!!!

[quote=ManicMic;26644]Going off the top of my head at the moment but do as kev said....

Switch off Engine Run switch, switch OFF Key switch. Press both SELECT & RESET buttons and then switch ON Key switch. Keep SELECT & RESET buttons pressed for at least 8 seconds. Display then changes to "DIAG". Release SELECT & RESET buttons.
Select CO1 mode by pressing the SELECT button.

Then press both the select and reset buttons together until you hear a click.

Then you will see a "0" in the top right of your speedo.

Then start your bike and you can see your rpm.


hey, sorry to bother, i done this step by step a couple of times but i see the "0" when i turn the throttle still "0" ???

its an 06

Hi Telesi, I can't think of why the reading would be 0 if you have started the bike, there should be a reading for RPM when you give it a rev... one of the XT guru's should be along soon to help you out, best of luck with it

thx, i will just keep trying maybe i will get lucky :)

Switch off Engine Run switch, switch OFF Key switch. Press both SELECT & RESET buttons and then switch ON Key switch. Keep SELECT & RESET buttons pressed for at least 8 seconds. Display then changes to "DIAG". Release SELECT & RESET buttons.
Select CO1 mode by pressing the SELECT button.

Then press both the select and reset buttons together until you hear a click.

Then you will see a "0" in the top right of your speedo.

Then start your bike and you can see your rpm.


hey, sorry to bother, i done this step by step a couple of times but i see the "0" when i turn the throttle still "0" ???[/quote]


Sorted out, just had to change the co number up or down a number, and then hit the switch on and start the bike!

There's a lot of info about the C1 setting but what is the C2 setting for?

I have a 2008 XT660Z Tenere...

When doing:
Switch off Engine Run switch, switch OFF Key switch. Press both SELECT & RESET buttons and then switch ON Key switch. Keep SELECT & RESET buttons pressed for at least 8 seconds. Display then changes to "DIAG". Release SELECT & RESET buttons.

The only thing that happens is that the clock is starting to count up and I can change my Clock settings. Which is not a bad thing though... But not really what I would like to do! :)
What am I doing wrong, or is there any differences between years?

Any help is appreciated!

There is no diagnostic mode on the Tenere dash! You will need to get one of these...

http://www.off-the-road.de/out/pictu...ag_modul_2.jpg

I bought one and I have to say it was �90 well spent.

Rev counter
 

Hi all, I follow all the instructions and get the rev counter on screen but when I start the engine it stays at 0. I have tried this with the engine warm and cold but I can not get it to read.2004 XTX.help:gobain:
Cheers
Croxalla

Rev Counter
 

I have followed all the instuctions to display the revs on my 2004 XT660X and the display stays at zero. I did notice the CO1 CO2 displays on my bike display C1 and C2, maybe the computer system is slightly different ?

Has anyone managed to do this on a 2004 model of this bike ??

Thanks.

One other thing to note (as you will see when you do this) - is that all you get on the screen is the rev counter, the rest of the screen remains blank.

I was hoping to see what rpm i was doing at what speed, and although i had to guess the speed, this has still given me a better insight to the engine to what i had before.

Carry on :icon_biggrin:

what a shame that the option of the rpm can not be left fixed

Xt1200z


Sent from my iPhone using Tapatalk

I think youre talking about a 660 not a 1200 z? Sorry dint read back 3 pages lol but the person asking about co2 rather then co1 . Co2 does nothing as that is for second cylinderd cylinder which the 600s dont have

Rising the old thread.
Today I tried to check idle speed, but bike refused to listen me. When I try to wake up the rev counter on the screen, engine will just start with the normal screen. The last time when I checked the idle speed, bike behaved same, but after several attempts it accepted the commands. XTR 2007.
Anyone with similar experience who can give me advice about solving this issue?
Petre

Sorted. Disconnect the battery for a while.