.: XT660.com - The #1 XT660 Resource :.

.: XT660.com - The #1 XT660 Resource :. ( https://www.xt660.com/index.php)
-   XT660Z T�n�r� Tech Section ( https://www.xt660.com/forumdisplay.php?f=163)
-   -   XT660Z not starting ( https://www.xt660.com/showthread.php?t=23364)

rangy01 16-01-15 23:51

XT660Z not starting
 
My xt660z (2011) refuses to start after a long ride. Error code 12 appears when ign turned on, and the engine light flashes quickly when start button pushed.
If left for a day or so it will usually start again. I have checked crank sensor resistance, when in running condition and when not running, both good.
Checked wires and terminals but still have the problem. I have read where other owners have had a similar issue, but cant find any fix. Any ideas would be great.
Thanks
Andy

Pleiades 17-01-15 18:56

Does it only do it after a long ride? I take it it's OK on short journeys and when you just start it, run it, stop it, and start it again?

There are a number of faults that can cause the Engine Trouble light to flash when the starter is pressed - coil, lean-angle switch and a couple of ECU wiring related one that I can't remember off-hand. They all have higher number fault codes (higher than 12). Thing is the fault code displayed on the dash is only ever the lowest if there is more than one, so there might be something else afoot which you don't know about.

The long run/hot engine thing suggests maybe coil primary windings breaking down. Or perhaps a wiring fault which gives an increased high resistance when hot. I'm clutching at straws. Anyway, for now, if the crank position sensor is within spec and the wiring looks intact, check the coil and lean-angle cut-off switch. The starter relay (and start cut-off relay) can also give the flashing ET light, so check them too, as can faults with the associated components that feed the cut-off relay with data: side stand switch, neutral switch and clutch switch.

Unless you can get to/find a diagnostic tool (they aren't expensive and IMO well worth having), you won't be able to read all the fault codes if there are several (just the lowest). The bike's new to you, so is it under warranty? Trip to the dealer maybe?

rangy01 17-01-15 22:43

Thanks for that info. I havet tested the side stand switch and neutral switch, will check the lean angle next. I didn't know about the multiple error code situation, booked in for check at local dealer, so will see what he comes up with. ( Bike is out of warranty, but only done 7,000 K's )
Thanks again
Andy

x3zter 15-06-18 20:15

Quote:

Originally Posted by rangy01 (Post 205832)
Thanks for that info. I havet tested the side stand switch and neutral switch, will check the lean angle next. I didn't know about the multiple error code situation, booked in for check at local dealer, so will see what he comes up with. ( Bike is out of warranty, but only done 7,000 K's )
Thanks again
Andy

Hi, I got the same issue, (error code 12, no start) you got a solution? thank you!

Chalk Two 15-06-18 22:07

this diagnostic tool is specific for the Tenere. Maybe if you asked ClubeXt on Facebook, you might find a local owner who can help.

esta ferramenta de diagn�stico � espec�fica do Tenere. Talvez se voc� perguntasse ao ClubeXt no Facebook, voc� poderia encontrar um dono local que possa ajudar.




https://www.cmsnl.com/products/fi-di.../#.WyQbiqdKhPY


All times are GMT +1. The time now is 01:12.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.